FPV Quad Parts

Peripherals and Replacement Parts

Equipment

Equipment Peripherals

Build Page Parts

Build Parts Equipment

Pre-Built Quads and Kits 

Build Page Parts Overflow

Build Parts Equipment Overflow

Compatibility Categories

Flite Test

Flite Test FT EZ ID - Remote ID Module

FT EZ ID was created to not only provide compliance with current FAA regulations, but also bring features that many will find valuable and useful in everyday flying activity. - 100% both designed and manufactured in the United States, thanks to a tremendous amount of hard work between Flite Test, Tritium Electronics, a

Flite Test FT EZ ID - Remote ID Module w/ Plug

FT EZ ID was created to not only provide compliance with current FAA regulations, but also bring features that many will find valuable and useful in everyday flying activity. FT EZ ID is 100% both designed and manufactured in the United States.

Flight Controller Part Type

Flight Controller Parts and Other Electronics

iFlight

iFlight BLITZ Mini M10 GPS, Compass V2

IFLIGHT











The newly upgraded BLITZ Mini M10 GPS V2 has arrived, offering faster and more stable satellite search with the 10th generation chipset. This advancement in technology provides users with a more reliable and efficient GPS experience. This GPS also has a compass built-in.










Check out our other GPS modules, as well as the rest of our iFlight Products
Features

UBLOX M10 chip
Compass module QMC5883L integrated
Built-in farad capacitor for faster hot start
18.2x18.2mm GPS ceramic antenna, low power consumption, strong signal, lightweight.
Onboard LNA (Low Noise Amplifier), RF filter, and TCXO (temperature-compensated crystal oscillator)
10 Hz Refresh rate
Built-in Flash

Specifications

Compass module: QMC5883L
Baud Rate: 9600bps-460800bps (Default - 115200bps)
Sensitivity: Tracking: -167dBm
Cold start: 27s
Hot start: 1s
Maximum height: 80000m
Maximum speed: 500 m/s
Speed accuracy: 0.05 m/s
Maximum acceleration: ≦ 4G
Refresh Rate: 10 Hz
GPS patch antenna size: 18.2 x 18.2 x 4 mm
Total dimensions: 20 x 21 x 8 mm
Weight: 8g
Input Voltage: 3.3-5.5 V
GPS pin definition: RX/TX UART
Compass pin definition: SDA/SLA
GNSS: GPS+SBAS+Galileo+QZSS+Glonass

Includes

1x iFlight Mini M10 GPS V2
1 x Cable set



The newly upgraded BLITZ Mini M10 GPS V2 has arrived, offering faster and more stable satellite search with the 10th generation chipset. This advancement in technology provides users with a more reliable and efficient GPS experience. This GPS also has a compass built-in. Check out our other GPS modules, as well as the 

iFlight BLITZ Mini M10 GPS & Compass V2

The newly upgraded iFlight BLITZ Mini M10 GPS V2  has arrived, offering faster and more stable satellite search with the 10th generation chipset. 

iFlight BLITZ Mini M10 GPS V2

HolyBro

Holybro Pix32 V6 Baseboard

Holybro

The Holybro Pix32 V6 Baseboard carries the Holybro Pix32 V6 Flight Controller. It connects with a 100-pin connector.

Pololu

Pololu Step-Down Voltage Regulator 

The&nbspPololu 9V, 5A Step-Down Voltage Regulator&nbspis a&nbsppowerful step-down (or buck) regulator that takes an input voltage of up to 50&nbspV and efficiently reduces it to&nbsp9&nbspV.

The Pololu 9V, 5A Step-Down Voltage Regulator is a powerful step-down (or buck) regulator that takes an input voltage of up to 50 V and efficiently reduces it to 9 V.

Pololu 9V, 5A Step-Down Voltage Regulator

The compact (0.5″ × 0.7″) D24V10F12 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 12 V while allowing for a maximum output current of 1 A.

Pololu 12V, 1A Step-Down Voltage Regulator

The&nbspPololu 12V, 4.5A Step-Down Voltage Regulator&nbspis&nbspa powerful step-down (or buck) regulator that takes an input voltage of up to 50&nbspV and efficiently reduces it to&nbsp12&nbspV.&nbsp

The Pololu 12V, 4.5A Step-Down Voltage Regulator is a powerful step-down (or buck) regulator that takes an input voltage of up to 50 V and efficiently reduces it to 12 V. 

Pololu 12V, 4.5A Step-Down Voltage Regulator

The Pololu 12V, 2.4A Step-Down Voltage Regulator is a synchronous switching step-down (or buck) regulator that takes an input voltage of up to 50V and efficiently reduces it to 12V.

Pololu 12V, 2.4A Step-Down Voltage Regulator

The Pololu 9V, 2.6A Step-Down Voltage Regulator is a synchronous switching step-down (or buck) regulator that takes an input voltage of up to 50V and efficiently reduces it to 9V.

Pololu 9V, 2.6A Step-Down Voltage Regulator

The Pololu 5V, 3.2A Step-Down Voltage Regulator is a synchronous switching step-down (or buck) regulator that takes an input voltage of up to 50V and efficiently reduces it to 5V.

Pololu 5V, 3.2A Step-Down Voltage Regulator

The&nbspPololu 5V, 5.5A Step-Down Voltage Regulator is a&nbspstep-down (or buck) regulator that takes an input voltage of up to 50&nbspV and efficiently reduces it to&nbsp5V.&nbsp

The Pololu 5V, 5.5A Step-Down Voltage Regulator is a step-down (or buck) regulator that takes an input voltage of up to 50 V and efficiently reduces it to 5V. 

Pololu 5V, 5.5A Step-Down Voltage Regulator

This&nbspPololu 5V, 5A Step-Down Voltage Regulator&nbspis a step-down (buck) regulator that generates a fixed 5 V output from input voltages up to 38 V.

This Pololu 5V, 5A Step-Down Voltage Regulator is a step-down (buck) regulator that generates a fixed 5 V output from input voltages up to 38 V.

Pololu 5V, 5A Step-Down Voltage Regulator

This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 9 V.

Pololu 9V, 2.5A Step-Down Voltage Regulator

This compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages between 4 V and 50 V and efficiently reduces them to a lower, user-adjustable voltage set by an on-board trimmer potentiometer. 

Pololu 2.5-7.5V 600mA Step-Down Voltage Regulator

Holybro DroneCAN M8N GPS

The DroneCAN M8N GPS is the primary CAN protocol used by the ArduPilot and PX4 projects for communication with CAN peripherals. It is an open protocol with open communication, specification, and multiple open implementations.

Holybro H-RTK F9P Base

Unlike the H-RTK F9P Helical, the&nbspH-RTK F9P Base&nbspby Holybro is equipped with a high-gain antenna. This model is best suited to use as a base station.&nbsp

Unlike the H-RTK F9P Helical, the H-RTK F9P Base by Holybro is equipped with a high-gain antenna. This model is best suited to use as a base station. 

Holybro H-RTK F9P Rover Lite GNSS 2nd GPS w/ 6-Pin Cable

The H-RTK F9P 2nd GPS is the latest differential high-precision GNSS positioning system series from Holybro.&nbsp

The H-RTK F9P 2nd GPS is the latest differential high-precision GNSS positioning system series from Holybro. 

Holybro H-RTK F9P Rover Lite GNSS w/ 10-Pin Cable

The H-RTK F9P is the latest differential high-precision GNSS positioning system series from Holybro.

Holybro Pixhawk PDB Board for Pixhawk 6X & 6C

This Holybro Pixhawk Power Distribution Board (PDB) is used for PM02, PM02D, or similar power modules. This PDB is perfect for the Pixhawk 6X &amp 6C products.

This Holybro Pixhawk Power Distribution Board (PDB) is used for PM02, PM02D, or similar power modules. This PDB is perfect for the Pixhawk 6X & 6C products.

Holybro Pixhawk PDB Board (for Pixhawk 6X & 6C) 

Holybro Pixhawk PDB Board (for Pixhawk 6X &amp 6C) 

Holybro Pixhawk PM02 V3 12S Power Module 

The PM02 Power Module is a simple way of providing the autopilot's flight controller with clean power from a LiPo battery, as well as current consumption and battery voltage measurements all through a 6-pos cable. The PM02 Power Module is designed to power an autopilot flight controller, an RC receiver, and APM accessories (GPS, radio).&nbsp

The PM02 Power Module is a simple way of providing the autopilot's flight controller with clean power from a LiPo battery, as well as current consumption and battery voltage measurements all through a 6-pos cable. The PM02 Power Module is designed to

Matek

Matek CAN-L431 AP Periph CAN Node

Matek Systems

The Mateksys CAN-L431 is an Adapter Node based on ArudPilot AP_Periph firmware.

MATEKSYS AP Periph CAN Node - CAN-L431

Matek CAN-L4-PWM AP Periph DroneCAN to PWM Adapter

The Mateksys CAN-L4-PWM is an Adapter Node based on ArudPilot AP_Periph firmware.

MATEKSYS AP Periph DroneCAN to PWM Adapter - CAN-L4-PWM

Matek SVPDB-8S Servo PDB w/ BEC 5.5-36V to 5-8.2V

The MATEKSYS Servo PDB w/ BEC 5.5-36V to 5-8.2V reduces circuit loss and voltage drop on servo power wires for big-scale RC Airplanes and flight controllers without dedicated BEC for servos.

MATEKSYS Servo PDB w/ BEC 5.5-36V to 5-8.2V - SVPDB-8S

Matek 150A Hall Effect Current Sensor 

The MATEKSYS Hall Effect Current Sensor is a 150A sensor with factory calibrated Offset and Sensitivity.

MATEKSYS Hall Effect Current Sensor - 150A 

Matek AP Periph GNSS, M10-L4-3100 GPS Module

Matek AP_PERIPH GNSS M10-L4-3100 (GPS+Compass+Barometer) M10-L4-3100 is based on ArudPilots’ AP_Periph firmware,  It is a GNSS+COMPASS+BAROMETER peripheral with CAN/DroneCAN and UART/MSP interfaces. M10-L4-3100 uses multi-constellation GNSS powered by u-blox MAX-M10S , MAX-M10S is a concurrent GNSS receiver which can r

Matek AP_PERIPH GNSS M10-L4-3100 (GPS+Compass+Barometer)

The MATEKSYS AP Periph GNSS, M10-L4-3100 GPS is equipped with AP_Periph L431 CAN node, MAX-M10S, RM3100, SPL06-001, DroneCAN protocol &amp UART_MSP, and many other cool specs that make this GPS a winner in the wing game!

The MATEKSYS AP Periph GNSS, M10-L4-3100 GPS is equipped with AP_Periph L431 CAN node, MAX-M10S, RM3100, SPL06-001, DroneCAN protocol & UART_MSP, and many other cool specs that make this GPS a winner in the wing game!

MATEKSYS AP Periph GNSS, M10-L4-3100 GPS Module

MATEK

The Matek AP_Periph Drone CAN GNSS - M10-L4-3100 has a GPS, Compass, and Barometer! Ready for whatever your aircraft can throw at it!
Check out our GPSs, BECs, PDBs, Sensors and all of our Matek Products!
Features

M10-L4-3100 is based on ArudPilots’ AP_Periph firmware, It is a GNSS+COMPASS+BAROMETER peripheral with CAN/DroneCAN and UART/MSP interfaces.
M10-L4-3100 uses multi-constellation GNSS powered by u-blox M10 series , It is a concurrent GNSS receiver which can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS,Galileo, GLONASS and BeiDou can be received concurrently.
M10-L4-3100 integrates an industrial-grade compass PNI RM3100 which provides high resolution, low power consumption, no hysteresis, large dynamic range, and high sampling rates.

 
Specifications

ublox GNSS M10 series (GPS, GLONASS, Galileo and BeiDou)
Magnetic Compass: RM3100
Barometer: SPL06-001
Patch GNSS Antenna: 25x25x4mm
MCU STM32L431RCT6
UART3, onboard M10 GNSS module
UART2(TX2 RX2), MSP Protocol
CAN, DroneCAN Protocol
I2C JST-GH connector for external AirSpeed sensor
CAN bootloader LED, Blue

Fast blinking, Booting
Slow blinking, working

GNSS PPS LED, Green

solid on after powering on
blinking(1Hz) when GNSS has 3D fixed

3.3V LED, Red
Input voltage range: 4.5~5.3V (5V pad/pin)
Power consumption: 60mA
Operating Temperatures: -20~80 °C
Dimensions: 36mm*36mm*12mm
Weight:16g

Firmware

ArduPilot AP_Periph: MatekL431-GPS or MatekL431-Periph

Tips &amp Notes

on M10-F4-3100, The 3 magnetic coils have little solder paste to avoid the excess to “tilt” them, resulting in some reading inaccuracies of the compass. Any strong impacts will definitely separate them, especially the “tall coil” Sen-Z-f. Please use this precision module with care.
The default configuration on MAX-M10S with ublox FW5.1 is concurrent reception of GPS, Galileo, and BeiDou B1I with QZSS and SBAS enabled. GLONASS is disabled by default.
Beidou B1I (1561.098 MHz) and GLONASS can’t be enabled at the same time. Beidou B1C (1575.42 MHz) and GLONASS can be enabled at the same time. Flight controller firmware(INAV, Betaflight, ArduPilot) don’t support enable Beidou B1C for now.
with GPS, Galileo, and BeiDou B1I with QZSS and SBAS enabled, MAX-M10s can receive more than 30 Sats with HDOP down to 0.55.
Start with u-blox GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take up to 12.5 min. Probably PPS LED will not blink immediately after GPS has 3D fixed.

Includes

1x Matek AP_Periph Drone CAN GNSS - M10-L4-3100
2x JST-GH-4P to JST-GH-4P 20cm silicon wire
1x Mounting base (1x PCB plate, 4x silicon grommets, 4x Nylon standoffs M3x7, 4x Nylon screws M3x8)


The Matek AP_Periph Drone CAN GNSS - M10-L4-3100 has a GPS, Compass, and Barometer! Ready for whatever your aircraft can throw at it! Check out our GPSs, BECs, PDBs, Sensors and all of our Matek Products! Features M10-L4-3100 is based on ArudPilots’ AP_Periph firmware, It is a GNSS+COMPASS+BAROMETER peripheral with CAN

Matek AP_Periph Drone CAN GNSS - M10-L4-3100 - GPS

MenaceRC

MenaceRC Ultra Bright CobLEDs

Menace RC

The&nbspMenace RC CobLEDs&nbspare Ultra Bright and will light up your night! Get your sunglasses out here come the brightest RC LED&rsquos for your drone, plane, boat, car or any RC model.

The Menace RC CobLEDs are Ultra Bright and will light up your night! Get your sunglasses out here come the brightest RC LED’s for your drone, plane, boat, car or any RC model.

Menace RC Ultra Bright CobLEDs (Set of 4)

FETtec

FETtec KISS OSD Board

The FETtec OSD Board allows on-screen display of important data, as well as full-tuning of KISS parameters. Suitable for FETtec and KISS flight controllers.&nbsp&nbsp

The FETtec OSD Board allows on-screen display of important data, as well as full-tuning of KISS parameters. Suitable for FETtec and KISS flight controllers.  

FETtec OSD Board

OSD board for FETtec and KISS flight controllers. Allows on-screen display of important data as well as full tuning of KISS parameters.Check out our FC Accessories and the rest of our FETTEC Products! Specifications: Graphic OSD (STM32) Full KISS Tuning  Filter (PIDs, Rates, Settings) LED control (RGB LED, Racewire) VT

FETTEC OSD BOARD

Flywoo

Flywoo CineRace20 V1.2 Neon Led Frame

CineRace20 Frame kit is redesigned by the Flywoo team with a lot of attention to detail.  Inspired by RaceWhoops and designed by Free Zillion CineRace has a double ducted design - not just a simple guard anymore. This whoop can be as flexible as a racing drone, and as stable as Cinewhoop. Pilots can quietly enjoy the f

Flywoo CineRace20 V1.2 Neon Led Frame Kit

This&nbspNeon LED Frame Kit&nbspis for the&nbspFlywoo CineRace20. Featuring&nbspcolored ducts and colored neon LED strips to light up the sky on your starlight flights!

This Neon LED Frame Kit is for the Flywoo CineRace20. Featuring colored ducts and colored neon LED strips to light up the sky on your starlight flights!

Flywoo CineRace20 V1.2 Neon LED 2" CineWhoop Frame Kit

Flywoo CineRace20 V1.2 Neon LED 2&quot CineWhoop Frame Kit

Skystars

Skystars 4-36V to 9V 2A Step Down Voltage Regulator

SkyStars

A compact and simple voltage regulator that takes 4-36 volts input and steps the voltage down to 9V.

Skystars 2A Step Down Voltage Regulator (4-36V to 9V)

Skystars 4-36V to 5V 2A Step Down Voltage Regulator

A compact and simple voltage regulator that takes 4-36 volts input and steps the voltage down to 5V and can supply up to 2 amps for any of your 5 volt devices. Check out all our BEC/PDB section and the rest of our Skystars Products! Specifications: Brand name: Skystars RC Item Name: Step Down Voltage Regulator Input vo

Skystars RC 4-36V to 5V 2A Step Down Voltage Regulator

The&nbspSkyStars Mini 2A Step-Down Voltage Regulator Module&nbspis a&nbspcompact and simple voltage regulator that takes 4-36 volts input and steps the voltage down to 5V.&nbspSupplies up to 2A of power for any of your 5-volt devices.

The SkyStars Mini 2A Step-Down Voltage Regulator Module is a compact and simple voltage regulator that takes 4-36 volts input and steps the voltage down to 5V. Supplies up to 2A of power for any of your 5-volt devices.